1. Εισαγωγή
This manual provides comprehensive instructions for the installation, operation, and maintenance of your GLEDOPTO ZigBee Pro+ 5-in-1 Smart LED Controller, Model GL-C-204P. This device is designed to control various types of LED strip lights within a smart home environment, supporting multiple configurations including RGBCCT, RGBW, RGB, CCT, and Dimmer modes. It operates with a DC 12-48V input and offers a maximum total output of 15A.
2. Πληροφορίες Ασφάλειας
- Τομtage Συμβατότητα: Βεβαιωθείτε ότι η είσοδος voltage (DC 12-48V) and current of your power supply and LED strips are compatible with the controller's specifications. Exceeding the maximum total output current of 15A or 12A per channel can damage the device and connected lighting.
- Σωστή καλωδίωση: Always ensure good contact between the wire and the terminal. Incorrect or loose wiring can lead to overheating or malfunction.
- Λειτουργικό περιβάλλον: The controller is designed for indoor use within an operating temperature range of -20°C to +45°C. Avoid exposure to extreme temperatures, moisture, or corrosive environments.
- Συμβατότητα Hub: Please note that Tuya Zigbee hubs currently block third-party devices. This GLEDOPTO Zigbee product may not connect to Tuya hubs. Verify compatibility with your specific Zigbee hub before purchase and installation.
- Επαγγελματική εγκατάσταση: If you are unsure about any wiring procedures, consult a qualified electrician.
3. Περιεχόμενα συσκευασίας
- 1 x GLEDOPTO ZigBee Pro+ LED Strip Controller (Model GL-C-204P)
4. Το προϊόν τελείωσεview
The GLEDOPTO ZigBee Pro+ controller offers versatile control for various LED strip types. Its compact design integrates essential functions for smart lighting systems.
Εικόνα 4.1: Εμπρός view of the GLEDOPTO ZigBee Pro+ 5-in-1 Smart LED Controller.
Βασικά Χαρακτηριστικά:
- Υψηλό ρεύμα εξόδου: Total output current of 15A maximum, with a maximum of 12A per single channel, allowing for longer LED strip installations (e.g., 10-15 meters).
- Wide VoltagΕύρος e: Supports DC 12-48V input, compatible with a broad range of LED strips and panel lights.
- Λειτουργικότητα 5 σε 1: Configurable for RGBCCT, RGBW, RGB, CCT, or Dimmer LED strip types.
- Power-on Status Memory: Retains the last power-on state (on/off) or defaults to 'on' after a power interruption.
- Selectable PWM Frequency: Offers frequencies of 600Hz, 800Hz, 1000Hz, 2000Hz, 4000Hz, and 8000Hz to match various power supplies and reduce potential noise. Default frequency is 1000Hz.
Εικόνα 4.2: Λεπτομερής view of the controller highlighting its 15A maximum output, support for external push button switches, and quick wire connectors for easy wiring.
Συστατικά:
Image 4.3: Diagram illustrating the key functions and components of the controller.
- Κουμπί επαναφοράς: Used for switching PWM frequency (short press) or resetting the controller (long press for 5 seconds).
- OPT Button: Used for switching the current device function/mode (short press) or setting power-on status (long press for 5 seconds).
- Push Button Terminal: Connects to an external push button for power on/off (short press) and brightness adjustment (long press).
- Ενδεικτική λυχνία: Displays different colors corresponding to the selected function mode.
5. Ρύθμιση
5.1 Οδηγίες καλωδίωσης
The controller features quick-connect terminals for simplified wiring. Follow these steps for secure connections:
- Προετοιμασία καλωδίων: Strip approximately 10mm of insulation from the ends of your LED strip wires and power supply wires. The suggested wire type is 0.3-2mm² (22-14AWG).
- Άνοιγμα εφαρμογής σύνδεσης: Gently open the connector lever upwards.
- Εισαγωγή καλωδίου: Insert the prepared wire into the appropriate terminal. Refer to the terminal labels for correct polarity and channel assignment (V+, R, G, B, W, C, V-).
- Ασφαλής σύνδεση: Press the connector lever down to secure the wire. Give each wire a gentle tug to ensure it is firmly held.
Image 5.1: Step-by-step guide for using the quick connect port design for wiring.
5.2 Σύζευξη με ZigBee Hub
This controller requires a compatible ZigBee hub for smart control. The pairing process typically involves:
- Ενεργοποίηση: Connect the controller to a suitable DC 12-48V power supply.
- Έναρξη λειτουργίας σύζευξης: Consult your ZigBee hub's instructions to put it into pairing mode.
- Επαναφορά ελεγκτή: Short press the 'Reset' button on the controller or power cycle the controller (turn off and on) to initiate pairing. The indicator light may flash to confirm pairing mode.
- Επιβεβαίωση ζεύξης: Once successfully paired, the controller will appear in your ZigBee hub's device list.
Important Note: If you change the device function mode using the 'OPT' button, the controller may need to be re-paired with your ZigBee hub.
6. Οδηγίες λειτουργίας
6.1 Mode Selection (5-in-1 Functionality)
The controller supports five different LED strip configurations. Use the 'OPT' button to cycle through these modes:
- Short Press 'OPT': Switches the current device function. The indicator light will change color to reflect the selected mode:
| Χρώμα φωτός ένδειξης | Τρόπος |
|---|---|
| Λευκό | RGB + CCT |
| Κίτρινος | RGBW |
| Μπλε | RGB |
| Πράσινος | CCT |
| Κόκκινος | Dimmer |
Image 6.1: Visual representation of the 5-in-1 modes supported by the controller.
6.2 Power-on Status Settings
You can configure the controller's behavior after a power interruption:
- Long Press 'OPT' (more than 5 seconds): The indicator light will flash light blue three times. This action toggles between two power-on states:
- Θυμηθείτε την τελευταία κατάσταση: The controller will resume its state (on/off) prior to the power failure.
- Lights Up by Default: The controller will turn on automatically when power is restored.
Image 6.2: Illustration of the two optional power-on state settings.
6.3 Selectable PWM Frequency
Adjusting the PWM frequency can help match different power supplies and reduce audible noise (e.g., high-pitched whine) from the LED strips or power supply.
- Short Press 'Reset': Cycles through the available frequencies. The number of flashes of the indicator light corresponds to the selected frequency:
| Αναβοσβήνει | Συχνότητα |
|---|---|
| 1 | 600Hz |
| 2 | 800Hz |
| 3 | 1000 Hz (Προεπιλογή) |
| 4 | 2000Hz |
| 5 | 4000Hz |
| 6 | 8000Hz |
Image 6.3: Diagram illustrating the selectable PWM frequencies and their corresponding indicator light flashes.
6.4 External Push Button Control
An external push button can be connected to the 'Push' terminals for basic control:
- Σύντομος Τύπος: Εναλλάσσει την ενεργοποίηση/απενεργοποίηση της τροφοδοσίας.
- Παρατεταμένο πάτημα: Adjusts brightness. Release and long press again to change dimming direction (increases brightness, then decreases brightness).
7. Συντήρηση
- Καθάρισμα: Use a dry, soft cloth to clean the controller. Do not use harsh chemicals or abrasive cleaners.
- Περιβάλλο: Keep the controller in a dry, well-ventilated area, away from direct sunlight and sources of heat or moisture.
- Συνδέσεις: Periodically check all wire connections to ensure they remain secure.
8. Αντιμετώπιση Προβλημάτων
- Ο ελεγκτής δεν ανταποκρίνεται:
- Βεβαιωθείτε ότι η παροχή ρεύματος είναι συνδεδεμένη και παρέχει τη σωστή τάσηtagε (DC 12-48V).
- Ελέγξτε όλες τις συνδέσεις καλωδίωσης για χαλαρότητα ή λανθασμένη πολικότητα.
- Try power cycling the controller (disconnect and reconnect power).
- If using a ZigBee hub, ensure the controller is properly paired. Re-pair if necessary.
- LED Strips Not Lighting Up or Flickering:
- Verify that the LED strip type matches the mode selected on the controller (RGBCCT, RGBW, RGB, CCT, Dimmer).
- Check the LED strip itself for damage or incorrect wiring.
- Ensure the total current draw of the LED strips does not exceed the controller's maximum output (15A total, 12A per channel).
- If flickering occurs, try adjusting the PWM frequency using the 'Reset' button.
- Υψηλός θόρυβος:
- This can often be resolved by changing the PWM frequency. Short press the 'Reset' button to cycle through frequencies (600Hz, 800Hz, 1000Hz, 2000Hz, 4000Hz, 8000Hz) until the noise is eliminated or reduced.
- Υπερθέρμανση ελεγκτή:
- Αποσυνδέστε αμέσως την παροχή ρεύματος.
- Check if the total current draw of the connected LED strips exceeds the controller's maximum capacity (15A total).
- Βεβαιωθείτε ότι υπάρχει επαρκής αερισμός γύρω από το χειριστήριο.
- Verify that all wire connections are secure and not causing resistance.
- Cannot Connect to Tuya Hub:
- As stated in the safety information, Tuya Zigbee hubs may block third-party devices. This is a known compatibility issue. Consider using a different Zigbee hub (e.g., Home Assistant, Conbee) for full functionality.
9. Προδιαγραφές
Image 9.1: Detailed product parameters for the GLEDOPTO ZigBee Pro+ LED Controller.
| Παράμετρος | Αξία |
|---|---|
| Μοντέλο Αρ. | GL-C-204P |
| Είσοδος Voltage | DC 12-48V |
| Ρεύμα/Κανάλι εξόδου | 12A Μέγ |
| Συνολικό ρεύμα εξόδου | 15A Μέγ |
| Θερμοκρασία λειτουργίας | -20°C έως +45°C |
| Πρωτόκολλο επικοινωνίας | ZigBee + 2.4G RF |
| Suggested Wire Type | 0.3-2mm² (22-14AWG) |
| Μήκος απογύμνωσης | 10 mm |
| Υλικό | Πυροσβεστικός υπολογιστής |
| Καθαρό Βάρος | 54.2 γρ |
| Μικτό βάρος | 64.8 γρ |
| Διαστάσεις (Μ x Π x Υ) | 108 x 45 x 18 mm (4.25 x 1.77 x 0.71 ίντσες) |
10. Εγγύηση και υποστήριξη
GLEDOPTO products are designed for reliability and performance. For warranty information and technical support, please refer to the official GLEDOPTO webστον ιστότοπο ή επικοινωνήστε απευθείας με την εξυπηρέτηση πελατών. Κρατήστε την απόδειξη αγοράς σας ως απόδειξη αγοράς για τυχόν αξιώσεις εγγύησης.
