Πακέτο λειτουργιών BLE κόμβου IoT STM32Cube

Προδιαγραφές

• Όνομα προϊόντος: VL53L3CX-SATEL
• Function Pack: STM32Cube function pack for IoT node BLEconnectivity and time-of-flight sensors (FP-SNS-FLIGHT1)
• Έκδοση: 4.1 (31 Ιανουαρίου 2025)

Hardware Overview
The VL53L3CX-SATEL is a breakout board with the VL53L3CX time-of-flight sensor.

Βασικά Χαρακτηριστικά

• Υποδοχή Arduino UNO R3
• BLUENRG-M2SP για συνδεσιμότητα Bluetooth χαμηλής ενέργειας
• M95640-RMC6TG για αποθήκευση στη μνήμη

Περιγραφή λογισμικού:
The firmware update (FOTA) feature allows for easy software updates.

Απαιτήσεις λογισμικού:
Compatible with STM32 Nucleo development boards, specificallyNUCLEO-F401RE, NUCLEO-L476RG, or NUCLEO-U575ZI-Q.

Πρόσθετες πληροφορίες:
For firmware updates, refer to the latest information available at www.st.com.

Οδηγίες χρήσης προϊόντος

Setup & Demo Examples

Βήμα 1: Ρύθμιση υλικού
Connect the VL53L3CX-SATEL breakout board to an STM32 Nucleo development board (NUCLEO-F401RE, NUCLEO-L476RG, or NUCLEO-U575ZI-Q) using the appropriate connectors.

Βήμα 2: Ρύθμιση λογισμικού
Ensure that the necessary software prerequisites are installed on your system as specified in the documentation.

Βήμα 3: Επίδειξηamples
Ανατρέξτε στο παρεχόμενο demo examples to understand how to interact with the VL53L3CX sensor using the provided software architecture.

Το υλικό και το λογισμικό τελειώνουνview

Sample implementations are available for STM32 Nucleo development boards plugged into STM32 Nucleo expansion boards:

• NUCLEO-F401RE (or NUCLEO-L476RG or NUCLEO-U575ZI-Q) + X-NUCLEO-BNRG2A1 + X-NUCLEO-53L3A2
• NUCLEO-F401RE (or NUCLEO-L476RG or NUCLEO-U575ZI-Q) + X-NUCLEO-BNRG2A1 + X-NUCLEO-53L3A2

Πλακέτα επέκτασης χαμηλής ενέργειας Bluetooth

Περιγραφή υλικού

• The X-NUCLEO-BNRG2A1 is a Bluetooth Low Energy (BLE) evaluation and development board system, designed around ST’s BLUENRG-M2SP Bluetooth Low Energy module based on BlueNRG-2.
• The BlueNRG-2 processor hosted in the BLUENRG-M2SP module communicates with the STM32 microcontroller, hosted on the Nucleo development board, through an SPI link available on the Arduino UNO R3 connector.

Βασικό προϊόν επί του σκάφους

• BLUENRG-M2SP Bluetooth Low Energy, FCC and IC certified (FCC ID: S9NBNRGM2SP, IC: B976C-BNRGM2SP), module based on Bluetooth® Low Energy wireless network processor BlueNRG-2, BLE v5.0 compliant.
• BLUENRG-M2SP integrates a BALF-NRG-02D3 balun and a PCB antenna. It embeds a 32 MHz crystal oscillator for the BlueNRG-2.
• M95640-RMC6TG 64-Kbit serial SPI bus EEPROM with high-speed clock interface

X- NUCLEO-53L1A2 Hardware Description

• The X-NUCLEO-53L3A2 is a ranging sensor with multi-target detection evaluation and development board designed around the VL53L3CX sensor based on ST FlightSense Time-of-Flight technology.
• Το VL53L3CX επικοινωνεί με τον μικροελεγκτή κεντρικού υπολογιστή της πλακέτας προγραμματιστή STM32 Nucleo μέσω μιας σύνδεσης I2C που είναι διαθέσιμη στην υποδοχή Arduino UNO R3.

Βασικό προϊόν επί του σκάφους

• VL53L3CX Time-of-Flight (ToF) ranging sensor with multi-target detection
• 0.25, 0.5, and 1mm spacers to simulate air gaps, with the cover glass
• Cover window (made by Hornix) sample with low cross-talk,k ready to use / clipable on VL53L3CX
• Two VL53L3CX breakout boards

Περιγραφή υλικού VL53L3CX-SATEL

• The VL53L3CX-SATEL breakout boards can be used for easy integration into customer devices. Thanks to the voltagΜε ρυθμιστή και μετατοπιστές στάθμης, μπορεί να χρησιμοποιηθεί σε οποιαδήποτε εφαρμογή με τροφοδοσία από 2.8 V έως 5 V.
• The PCB section supporting the VL53L3CX module is perforated so that developers can break off the mini-PCB for use in a 2.8 V supply application using flying leads.

Βασικό προϊόν επί του σκάφους

• VL53L3CX Time-of-Flight (ToF) ranging sensor with witmulti-targetet detection
• Regulator: 5 to 2.8 V range input voltage (εξόδου τόμtage: 2.8 V)
• VL53L3CX signal interface level shifter

Σημαντικές πρόσθετες πληροφορίες υλικού

BlueNRG-2 library does not work with the stock firmware that is loaded in the BLE module of the X-NUCLEO-BNRG2A1 expansion board.
Για το λόγο αυτό:

• First of all, it is needed to solder on X-NUCLEO-BNRG2A1; if it is not soldered, a 0-ohm resistor at R117.
• Then you can use a standard ST-Link V2-1 with 5 jumper wires female-female together with the TSW-BNRGFLASHER software tool (currently available only for Windows PC) to update the firmware of the BLE module of X-NUCLEO-BNRG2A1.

Πρέπει να συνδέσετε τις ακίδες J12 του X-NUCLEO-BNRG2A1 στις ακίδες του ST-Link V2-1 όπως φαίνεται στην εικόνα και να ακολουθήσετε τα βήματα που φαίνονται στην επόμενη διαφάνεια.
In particular, we have the following connections:

	J12	ST-Link V2-1
Καρφίτσα	1	1
Καρφίτσα	2	9
Καρφίτσα	3	12
Καρφίτσα	4	7
Καρφίτσα	5	15

1. Install the ST BlueNRG-1_2 Flasher Utility and open it, then select the SWD tab.b
2. Erase the flash memory of the BlueNRG-2 chip.
3. Download the Link Layer Only firmware for the BLE module from the following link: DTM_LLOnly. binn
4. Load the Link Layer Only firmware in the ST BlueNRG-1_2 Flasher Utility and then press the “Flash” button.
5. If you need to restore the stock firmware of the BLE module of X-NUCLEO-BNRG2A1, you can repeat the procedure using this firmware image DTM_Full.bi.n
6. If you should find some issues during the update process, you can try to repeat the procedure closing the J15 jumper on the X-NUCLEO-BNRG2A1 expansion board.

	VL53L3CX-SATEL	Υποδοχή Arduino	NUCLEO-F401RE NUCLEO-L476RG	NUCLEO-U575ZI-Q
SCL	2	Δ15	PB8	PB8
SDA	4	Δ14	PB9	PB9
XSDN	3	D4	PB5	PF14
VDD_SENSOR	5	3V3	CN6 ακίδα αρ. 4	CN8 ακίδα αρ. 7
GND_X	6	GND	CN6 ακίδα αρ. 6	CN8 ακίδα αρ. 11

Περιγραφή λογισμικού

• The FP-SNS-FLIGHT1 is an STM32Cube function pack, which lets your IoT node connect to a smartphone via BLE and uses a suitable Android or iOS application like the STBLESensor app to view Δεδομένα απόστασης αντικειμένου σε πραγματικό χρόνο που διαβάζονται από τον αισθητήρα Χρόνου Πτήσης.
• The package also enables advanced functions, such as presence detection within a fixed range.
• This package, together with the suggested combination of the STM32 and ST devices, can be used to develop wearable applications or smart thing applications in general.
• The software runs on the STM32 microcontroller and includes all the necessary drivers to recognize the devices on the STM32 Nucleo development board.

Βασικά χαρακτηριστικά

• Complete firmware to develop an IoT node with BLE connectivity, and Time-of-Flight sensors
• Compatible with STBLESensor application for Android/iOS to perform distance data reading and firmware update (FOTA)
• Multitarget ranging sensor application based on the VL53L3CX Time-of-Flight (ToF) sensor
• Sample implementation available for X-NUCLEO-53L3A2 (or VL53L3CX-SATEL) and X-NUCLEO-BNRG2A1 connected to a NUCLEO-F401RE or NUCLEO-L476RG or NUCLEO-U575ZI-Q
• Compatible with STM32CubeMX, can be downloaded from and installed directly into STM32CubeMX
• Εύκολη φορητότητα σε διαφορετικές οικογένειες MCU, χάρη στο STM32Cube
• Δωρεάν φιλικοί προς τον χρήστη όροι άδειας χρήσης

Setup & Demo Examples

Λογισμικό και άλλες προϋποθέσεις

• STSW-LINK004
  • STM32 ST-LINK Utility (STSW-LINK004) is a full-featured software interface for programming STM32 microcontrollers
• FP-SNS-FLIGHT1
  • Αντιγράψτε το .zip file content of the firmware package into a folder on your PC.
  • Το πακέτο περιέχει πηγαίο κώδικα π.χamples (Keil, IAR, STM32CubeIDE) compatible with NUCLEO-F401RE, NUCLEO-L476RG, NUCLEO-U575ZI.
• ST BLE Sensor
  Application for Android (V5.2.0 or higher) /iOS (V5.2.0 or higher) to download from Google Store / iTunes

Ρύθμιση Ολοκληρώθηκεview: STM32 Nucleo με πλακέτες επέκτασης 

Ρύθμιση Ολοκληρώθηκεview

Προαπαιτούμενα υλικού με πλακέτες επέκτασης STM32 Nucleo 

• 1 x Bluetooth Low Energy expansion board (X-NUCLEO-BNRG2A1)
• 1 x STM32 ranging sensor expansion board (X-NUCLEO-53L3A2 or VL53L3CX-SATEL)
• 1 x STM32 Nucleo development board (NUCLEO-U575ZI-Q or NUCLEO-F401RE or NUCLEO-L476RG)
• 1x Android or iOS device
• 1 x PC with Windows 10 and above
• 1x USB type A to Mini-B USB cable for NUCLEO-F401RE or NUCLEO-L476RG
• 1x USB type A to Micro-B USB cable for NUCLEO-U575ZI-Q

Ξεκινήστε να γράφετε κώδικα σε λίγα μόνο λεπτά (1/3)

Ξεκινήστε να γράφετε κώδικα σε λίγα μόνο λεπτά (2/3)

1. How to install the pre-compiled binary:
   • For each application, there is inside the package one folder called “Binary”

Περιέχει:

• Για τα NUCLEO-F401RE και NUCLEO-L476RG:
  • pre-compiled FP-SNS-FLIGHT1 FW that could be flashed to a supported STM32 Nucleo for X-NUCLEO-53L3A2 using the STM32CubeProgrammer at the right position (0x08004000)
  • Important Note: This pre-compiled binary is compatible with the FOTA update procedure
  • pre-compiled FP-SNS-FLIGHT1 + BootLoader FW that could be directly flashed to a supported STM32 Nucleo for X-NUCLEO-53L3A2 using the STM32CubeProgrammer or by doing “Drag & Drop”
  • Important Note: This pre-compiled binary is not compatible with the FOTA update procedure
  • pre-compiled FP-SNS-FLIGHT1 FW that could be directly flashed to a supported STM32 Nucleo for VL53L3CX-SATEL using the STM32CubeProgrammer or by doing “Drag & Drop”
• Για το NUCLEO-U575ZI-Q:
  • pre-compiled FP-SNS-FLIGHT1 could be directly flashed to a supported STM32 Nucleo (for X-NUCLEO-53L3A2 and for VL53L3CX-SATEL) using the STM32CubeProgrammer or by doing “Drag & Drop”.
  • Important Note: For the first installation, after the full flash erase (suggested procedure), use the STM32CubeProgrammer to set the STM32 MCU user byte settings to use bank 1 for flashing the firmware and start the application

How to install the code after compiling the project for NUCLEO-F401RE and NUCLEO-L476RG:

• Compile the project with your preferred IDE

In the folder Utilities, there is a script *.sh that performs the following operations:

• Full Flash Erase
• Flash the right BootLoader at the right position (0x08000000)
• Flash the FLIGHT1 firmware at the right position (0x08004000)
  • This is the firmware that was compiled with the IDE
  • This firmware is compatible with the FOTA update procedure
• Save a complete Binary FW that includes both FLIGHT1 and the BootLoader
  • This binary can be directly flashed to a supported STM32 board using the ST-Link or by doing “Drag & Drop.”
  • Important Note:Thiss additional pre-compiled binary is not compatible with the FOTA update procedure

Before executing the *.sh script, it is necessary to edit it to set the installation path for STM32CubeProgrammer.
BootLoaderPath and BinaryPath as input are required when executing the .sh script.

Διαχείριση Flash και Διαδικασία Εκκίνησης

Λογισμικό Bluetooth χαμηλής ενέργειας και αισθητήρων

FP-SNS-FLIGHT1 για NUCLEO-F401RE / NUCLEO-L476RG / NUCLEO-U575ZI-Q – Παρακολούθηση σειριακής γραμμής (π.χ. Tera Term) 

Επίδειξη ExampΕφαρμογή αισθητήρα les ST BLE Πάνωview

Εφαρμογή αισθητήρα ST BLE για Android/iOS (1/5)

Hardware Features – Android Version

Εφαρμογή αισθητήρα ST BLE για Android/iOS (2/5)

Hardware Features – Android Version

ΣΗΜΕΙΩΜΑ
The presence is identified inside a fixed range of distances that can be modified by the line code:

• #define PRESENCE_MIN_DISTANCE_RANGE 300
• #define PRESENCE_MAX_DISTANCE_RANGE 800

Στο file FLIGHT1_config.h.h, which can be found in the Inc users folder for each project.

Εφαρμογή αισθητήρα ST BLE για Android/iOS (3/5)

Board Configuration – Android version

Εφαρμογή αισθητήρα ST BLE για Android/iOS (4/5)

Debug Console – Android version

Εφαρμογή αισθητήρα ST BLE για Android/iOS (4/5)

Firmware Upgrade – Android version

Εφαρμογή αισθητήρα ST BLE για Android/iOS (5/5)

Έγγραφα & Σχετικοί πόροι

FP-SNS-FLIGHT1: 

• DB2862: STM32Cube function pack for IoT node with NFC, BLE connectivity, and time-of-flight sensors – data brief
• UM2026: Getting started with the STM32Cube function pack for IoT node with NFC, BLE connectivity, and time-of-flight sensors – user manual
• Ρύθμιση λογισμικού file

X-NUCLEO-BNRG2A1

• Gerber files, BOM, Schematic
• DB4086: Bluetooth Low Energy expansion board based on the BLUENRG-M2SP module for STM32 Nucleo – data brief
• UM2667: Getting started with the X-NUCLEO-BNRG2A1 BLE expansion board based on BLUENRG-M2SP module for STM32 Nucleo – user manual

X- NUCLEO-53L3A2:

• Gerber files, BOM, Schematic
• DB4226: Time-of-Flight ranging sensor with multi-target detection expansion board based on VL53L3CX for STM32 Nucleo – data brief
• UM2757: Getting started with X-NUCLEO-53L3A2 multi target ranging ToF sensor expansion board based on VL53L3CX for STM32 Nucleo – user manual

VL53L3CX-SATEL:

• Gerber files, BOM, Schematic
• DB4194: VL53L3CX breakout board Time-of-Flight ranging sensor with multi-target detection – data brief
• UM2853: How to use the VL53L3CX with STMicroelectronics’ X-CUBE-TOF1 Time-of-Flight sensor software packages for STM32CubeMX – user manual

Συμβουλεύομαι www.st.com για την πλήρη λίστα

STM32 Open Development Environment: Overview

STM32 Open Development Environment: Fast, affordable Prototyping and Development

The STM32 Open Development Environment (STM32 ODE) is an open, flexible, easy, and affordable way to develop innovative devices and applications based on the STM32 32-bit microcontroller family combined with other state-of-the-art ST components connected via expansion boards. It enables fast prototyping with leading-edge components that can quickly be transformed into final designs

Για περισσότερες πληροφορίες, παρακαλούμε επισκεφθείτε www.st.com/stm32od.e

Σας ευχαριστώ

© STMicroelectronics – Με την επιφύλαξη παντός δικαιώματος.

Το εταιρικό λογότυπο της STMicroelectronics είναι καταχωρημένο εμπορικό σήμα του ομίλου εταιρειών STMicroelectronics. Όλα τα άλλα ονόματα αποτελούν ιδιοκτησία των αντίστοιχων κατόχων τους.

Συχνές Ερωτήσεις

• Ε: Μπορώ να χρησιμοποιήσω την πλακέτα VL53L3CX-SATEL με άλλες πλακέτες ανάπτυξης;
  A: The VL53L3CX-SATEL board is designed to be compatible with STM32 Nucleo development boards, ensuring optimal performance and functionality
• Ε: Πώς μπορώ να ενημερώσω το υλικολογισμικό στην πλακέτα VL53L3CX-SATEL;
  A: Firmware updates can be performed using the FOTA feature. Refer to the latest information available at www.st.com fordetailed instructions on firmware updates.

Έγγραφα / Πόροι

Πακέτο λειτουργιών BLE κόμβου ST STM32Cube IoT [pdf] Οδηγός χρήστη NUCLEO-F401RE, NUCLEO-L476RG, NUCLEO-U575ZI-Q, X-NUCLEO-BNRG2A1, XNUCLEO-53L3A2, VL53L3CX-SATEL, Πακέτο λειτουργιών BLE κόμβου IoT STM32Cube, STM32Cube, Πακέτο λειτουργιών BLE κόμβου IoT, Πακέτο λειτουργιών BLE

Αναφορές

• Εγχειρίδιο χρήστη